| 1. Confirm whether Section VIII applies | State the vessel’s maximum expected internal and external pressure, including relevant operating and upset conditions. Identify the required code edition and applicable jurisdiction. | ASME BPVC Section VIII, Division 1 generally covers vessels with internal or external pressure exceeding 15 psig, subject to the scope and exclusions in the applicable Code edition. The threshold alone does not determine every regulatory requirement. | Written code and jurisdictional basis for the equipment specification. |
| 2. Do not treat 15 psig as a universal exemption | For equipment at or below 15 psig, check applicable local laws, process-equipment requirements, and other relevant standards before deciding that no pressure-vessel rules apply. | The Section VIII scope threshold does not, by itself, establish that equipment below the threshold is unregulated or safe without pressure protection. | Documented review of applicable regulations and design standards. |
| 3. Define design pressure and MAWP clearly | Specify the required design pressure and design temperature, and ask the supplier to state the vessel’s calculated Maximum Allowable Working Pressure (MAWP) at the specified temperature. | Design pressure is a design input; MAWP is the pressure permitted by the completed vessel’s design under stated conditions. They are related but are not interchangeable. | Design calculations and nameplate data showing MAWP and its temperature basis. |
| 4. Include vacuum and external-pressure cases | State whether the vessel may be evacuated, exposed to vacuum, or subject to external pressure, and identify the conditions under which these cases can occur. | External-pressure stability can govern shell thickness or stiffening, even when internal operating pressure is low. | External-pressure design checks and the specified vacuum or external-pressure condition. |
| 5. Provide complete operating conditions | List normal, minimum, maximum, startup, shutdown, upset, and cleaning conditions as relevant, including pressure, temperature, fluid phase, and credible pressure transients. | Design conditions must reflect the service requirements established by the purchaser and responsible design engineer; normal operating values alone may not describe the governing case. | Approved process data sheet and written design-condition assumptions. |
| 6. Specify materials for the actual chemical service | Identify wetted materials, allowable alternatives, corrosion or erosion concerns, and any process-fluid contamination limits. Have material suitability reviewed for the actual concentration and temperature. | Material selection depends on the fluid and service conditions. A material permitted by a construction code is not automatically compatible with every process chemical. | Material specifications, material test reports where required, and documented compatibility review. |
| 7. State corrosion allowance and lining requirements | Specify any corrosion allowance and define lining, cladding, coating, or other protective-system requirements, including inspection and repair criteria. | Corrosion allowance is a design input, not a substitute for selecting a suitable material or protective system. Lining details can affect fabrication and inspection. | Approved drawings showing corrosion allowance and protective-system details. |
| 8. Define fabrication, welding, and examination requirements | Specify applicable Code construction requirements and any purchaser-required examination beyond the Code minimum. Identify weld details and access constraints that affect inspection. | Required examination depends on the applicable Code rules, design, materials, and joint details. Additional examination should be stated explicitly in the purchase specification. | Weld maps, examination records, and required personnel or procedure qualifications. |
| 9. Agree on pressure testing and acceptance | Identify the required pressure test method, test medium, acceptance criteria, and any constraints related to the process, materials, or site. | Hydrostatic and pneumatic testing have different hazards and Code requirements. Test pressure and procedure should be established under the applicable Code edition and approved design documentation. | Approved test procedure and completed pressure-test records. |
| 10. Require complete code and handover documentation | Specify the required Code certification, nameplate information, drawings, calculations, inspection records, and operating or maintenance documents before purchase. | Documentation requirements depend on the applicable Code edition, scope, jurisdiction, and purchase specification. Confirm the required certification route before placing the order. | Document index, final data report where applicable, certified drawings, and operating instructions. |
| Important: Confirm the governing ASME BPVC edition, applicable jurisdictional rules, and project-specific design basis with the responsible engineer and authority having jurisdiction. This table is a purchasing checklist, not a substitute for code interpretation or engineering design. |