| Spark plug | Resistor or non-resistor plug; thread, reach, and heat range are engine-specific | Ignition system on 25–52 cc two-stroke engines | Match the engine manual’s plug code, thread diameter, reach, and gap; do not select by engine capacity alone | Inspect at routine service; replace if fouled, damaged, or outside the recommended service schedule |
| Air filter element | Foam, felt, or layered filter media in model-specific shapes | Carbureted petrol brushcutters operating in dusty conditions | Compare the element’s length, width, thickness, sealing edge, and cover fit | Clean or replace more frequently in dusty environments; a filter must seal properly in its housing |
| Fuel line | Flexible fuel-resistant tubing; common small-engine sizes include approximately 2.5 mm internal diameter and 5 mm external diameter | Fuel tank, filter, and carburetor connections | Measure the original tubing and check whether the line must pass through a tank opening; confirm fuel compatibility | Replace if hardened, cracked, swollen, loose, or leaking |
| Fuel filter | In-tank pickup filter sized for the fuel line and tank opening | Fuel supply systems on small petrol engines | Check filter dimensions, outlet connection, tank opening, and compatibility with the intended fuel mixture | Inspect if fuel flow is restricted or the engine runs inconsistently; replace a contaminated or damaged filter |
| Primer bulb | Small-engine purge bulb; outer diameter and hose connections vary by carburetor system | Carburetors equipped with a manual priming or purge system | Compare bulb diameter, mounting style, number of hose ports, and port orientation | Replace if cracked, permanently collapsed, leaking, or unable to move fuel through the purge circuit |
| Carburetor | Diaphragm-type carburetor with model-specific metering and fuel-pump configuration | Fuel and air metering on two-stroke brushcutters | Match the engine model, mounting pattern, throttle linkage, choke arrangement, fuel connections, and impulse passage | Check for leaks, blocked passages, or damaged diaphragms; use the specified adjustment procedure after installation |
| Carburetor diaphragm and gasket set | Model-specific pump and metering diaphragms, gaskets, and inlet components | Serviceable diaphragm carburetors | Confirm the carburetor identification and the correct diaphragm sequence and shape | Replace hardened, stretched, torn, or distorted parts; keep fuel passages clean during service |
| Recoil starter assembly | Starter housing, pulley, spring, rope, and handle; mounting pattern varies by engine | Manual starting systems on petrol brushcutters | Check bolt spacing, housing clearance, rope exit position, pulley direction, and engagement design | Inspect if the rope frays, retracts poorly, or fails to engage; release spring tension carefully during repair |
| Starter rope and handle | Small-engine starter cord and pull handle; cord diameter and length depend on the starter assembly | Repair of a serviceable recoil starter | Measure the old cord diameter and required length; ensure the handle fits the cord and starter outlet | Replace frayed or damaged cord before it breaks during starting |
| Clutch shoe set | Centrifugal clutch shoes with springs; diameter and mounting details are engine-specific | Power transmission from engine to drive shaft | Match clutch diameter, shoe shape, spring arrangement, and crankshaft mounting | Replace worn, cracked, or contaminated shoes and damaged springs; verify that the cutting head does not rotate at idle |
| Clutch drum or drive cup | Drum designed for a specific clutch and drive-shaft connection | Clutch-to-drive-shaft interface | Check inner diameter, bearing arrangement, shaft connection, and compatibility with the clutch shoes | Inspect for scoring, excessive wear, overheating, or a loose fit when servicing the clutch |
| Flexible or solid drive shaft | Configuration and length depend on straight-shaft or curved-shaft design; common tube diameters include approximately 24, 26, and 28 mm | Power transmission through the brushcutter shaft assembly | Verify shaft length, tube diameter, end shape, spline count, and compatibility with the gearbox and clutch | Inspect for worn splines, bending, corrosion, or damaged flexible core; lubricate only as specified |
| Gearbox assembly | Angle-drive gearbox matched to the shaft tube and cutting attachment | Drive connection at the lower end of many straight-shaft brushcutters | Check tube diameter, mounting method, output thread, shaft engagement, and cutting-head compatibility | Check for excess play, noise, heat, or lubricant leakage; use the specified lubricant and service interval |
| Cutting line head | Bump-feed, manual-feed, or fixed-line head; attachment thread and line capacity vary | Grass and light vegetation cutting | Confirm spindle thread diameter and direction, adapter requirements, maximum line diameter, and guard suitability | Use line within the head’s stated diameter and length limits; replace cracked or badly worn components |
| Metal cutting blade | Multi-tooth or brush blade with a center bore commonly offered in sizes such as 20 mm or 25.4 mm | Suitable vegetation when the machine, guard, and operator instructions permit blade use | Match bore size, blade diameter, rotation direction, retaining hardware, and machine-rated maximum speed | Do not use a bent, cracked, or heavily worn blade; use the correct guard and approved retaining parts |
| Gearbox retaining hardware | Model-specific flange, washer, nut, and locking components | Secure mounting of a blade or compatible cutting head | Check thread direction, dimensions, seating surfaces, and compatibility with the gearbox spindle | Replace damaged or missing locking hardware; tighten using the machine’s prescribed method |
| Fuel tank cap and seal | Cap with model-specific thread, venting arrangement, and sealing gasket | Fuel tank closure | Confirm cap thread, diameter, vent design, and seal profile; an incorrect cap may affect fuel flow or leak | Replace if the cap or seal is cracked, leaking, or fails to close securely |
| Exhaust muffler and spark-arresting screen | Model-specific muffler assembly; screen requirements depend on the equipment and local regulations | Exhaust system on petrol brushcutters | Match mounting points, exhaust outlet, heat shield, and any required spark-arresting component | Inspect for loose fasteners, damage, or carbon blockage; service only when cool and follow local requirements |
| Anti-vibration mount or handle isolator | Rubber or elastomer isolator in a model-specific shape and mounting arrangement | Handle or engine-to-shaft vibration isolation | Compare mounting holes, dimensions, hardness specification, and orientation | Replace if split, detached, or excessively compressed; confirm all mounts are securely installed |